Do It Yourself Bath Setup.
Do It Yourself Bath Setup.
Blog Article
Everyone is bound to have his or her own opinion involving A Step-by-Step Guide to Installing a Bathtub.
Installing a bath tub isn't specifically rocket science, however it does require solid plumbing, woodworking, as well as in some cases, tiling skills. Replacing an old bathtub with a new one is additionally a moderately challenging project. If the old bathtub is easily available, the project can relocate rapidly; if you have to open a wall to eliminate the old tub and also place the new bathtub, the job is much harder. In either instance, the task is within a house handyman's skills, although you will certainly need a helper to vacate the old bathtub and embeded in the brand-new one. Ensure you have actually qualified yourself for the work as well as fit trying it. Rather than working with a specialist to take over a halfway-completed task, it is much better to take into consideration utilizing one prior to you start. Chances are you might need a specialist plumber to make tube connections.
This article will certainly help you mount a new bath tub in your restroom if you have actually currently bought a brand-new tub and also don't require to change the setup of your previous supply of water pipelines.
Your tools as well as material list should make up the following:
Removing Old Taps
If you need to change old taps with new ones as a part of your installment, then the first thing you ought to do is separate the water supply. After doing so, switch on the faucets to drain pipes any water staying in the system. The procedure of removing the existing taps can be rather bothersome because of the limited access that is typically the instance.
Use a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipes to the taps. Have a cloth ready for the staying water that will certainly originate from the pipelines. As soon as the supply pipes have been eliminated, utilize the exact same device to loosen up the nut that holds the faucets onto the bath/basin. You will need to stop the solitary taps from turning during this procedure. As soon as the faucets have actually been removed, the holes in the bath/basin will have to be cleaned of any type of old sealing compound.
Prior to carrying on to fit the brand-new faucets, contrast the pipeline links on the old faucets to the brand-new faucets. If the old faucets are longer than the new taps, then a shank adapter is required for the new taps to fit.
Fitting New Taps
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic adapter to stop damages to the string. One end of the adapter fits on the plastic tail of the faucet and also the various other end gives a link to the current supply pipes.
If you need to fit a monobloc, then you will require reducing couplers, which connects the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next off, place the faucet in the installing opening in the bath/basin making sure that the washing machines remain in area in between the faucet as well as the sink. Protect the tap in place with the manufacturer provided backnut. Once the faucet is firmly in position, the supply pipes can be connected to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with typical tap connectors. The former kind must be linked to the tap ends initially, tightening up only by hand. The supply pipes can later be attached to the various other end. Tighten both ends with a spanner after both ends have been attached.
Mounting the Tub
Using both wood boards under its feet, put the bathtub in the required placement. The wood boards are helpful in equally spreading out the weight of the tub over the area of the boards instead of concentrating all the weight onto 4 little points.
The next goal is to make certain that the tub is leveled all round. This can be accomplished by examining the level and readjusting the feet on the tub up until the spirit level reviews degree.
To install taps, fit all-time low of the outermost flexible tap adapter to the proper supply pipe by making a compression join; then do the very same for the various other tap.
Switch on the water as well as check all joints and also brand-new pipework for leaks and tighten them if essential. Fill up the bathtub as well as likewise examine the overflow outlet as well as the normal electrical outlet for leaks.
Lastly, fix the bathroom paneling as described in the maker's instruction manual. Tiling and also sealing around the bath tub should wait till the bathtub has actually been used at the very least once as this will certainly resolve it into its last setting.
Planning for the Installation
To start with, the supporting framework supplied with the bath should be fitted (if called for) according to the producer's guidelines. Next, fit the taps or mixer to the tub. When fitting the faucet block, it is important to see to it that if the tap features a plastic washer, it is fitted in between the bath as well as the faucets. On a plastic bath, it is likewise reasonable to fit a supporting plate under the taps device to prevent stress on the bath tub.
Fit the flexible faucet adapters to the bottom of both faucets utilizing 2 nuts and also olives (sometimes supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet through the hole in the bath. Make use of the nut supplied by the producer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the adaptable overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bath. Ensure you make use of every one of the supplied washing machines.
Attach the trap to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom should now prepare to be suited its final position.
Tiling Around the Tub
In the location where the bath meets the ceramic tile, it is needed to secure the joins with a silicone rubber caulking. This is essential as the installation can relocate sufficient to crack a rigid seal, triggering the water to permeate the wall surface in between the bathroom as well as the tiling, bring about complications with dampness and possible leakages to the ceiling listed below.
You can pick from a selection of coloured sealers to blend in your fixtures and fittings. They are offered in tubes and also cartridges, and are capable of sealing spaces as much as a size of 3mm (1/8 inch). If you have a bigger void to load, you can load it with spins of drenched paper or soft rope. Bear in mind to constantly load the bath tub with water prior to securing, to enable the motion experienced when the bathtub remains in usage. The sealer can split relatively very early if you do not take into consideration this motion prior to securing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are also easily available on the marketplace. It is suggested to fit the floor tiles making use of waterproof or water resistant sticky and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you enjoyed reading our part about Tools You Need to Install a New Bathtub . Thank you for taking a few minutes to browse our post. Appreciated our review? Please share it. Let somebody else find it. Thanks so much for your time invested reading it.
Schedule Now Report this page